I'm not sure why but to fix it: press alt-f1 then enter.
I would suggest disabling hardware raid and setting up software raid or no raid at all until the driver makes its way on the Linux Kernel, if guide it ever does.For example: for x in /proc/driver/cciss/cciss0-9* do echo "engage scsi" x done Once guide the scsi core is engaged by maintenance the driver, it cannot be disengaged guide (except by unloading the driver, if it happens to be linked as a module.) Note also that if no sequential.Post-install warnings about missing tg3 firmware in update-initramfs: installed firmware-linux-nonfree.See this page for a script that does this (Please note that you have to edit guide the script because it's supporting without changes only the outdated "lenny" and current stable "squeeze" release.).DL380 Gen9, smart Array P440ar, SAS, raid-1 guide o, worked fine.MicroServer G7 N54L Serial ATA raid-1 o You only need to edit the installer commandline to add dmraidtrue as explained in SataRaid wiki page.When off maintenance the iLO status LEDs flash like this: - 1, 3, 4, 6, 8 together - 5, 7 maintenance together - 2 off.Translation(s) : none, installer Compatibility Table, this table is a community maintained matrix.Installing the firmware-linux-nonfree package solves this issue (not sure if not installing it penalizes the CPU too much though).Alternatively, you can obtain non-official CD images with external firmware loading enabled; see Firmware. When starting the server this LEDs are on: - 2, 8 - after about 15 s: 3,.
And also lsscsi does only show the DVD drive, but no disks.
Repository details may be found at: m/SDR/project/mcp Or you installer may point apt directly at the repo with this line in /etc/apt/st: deb m/SDR/repo/mcp jessie/current non-free There's even a GPG key you can import in apt so it doesn't complain about untrusted sources.The installer will detect the absence of this firmware and prompt you for it at install-time.If you use the installer on the link it should work fine except for what was mentioned on the installation report.Maybe need to maintenance change termal swords sensors or see if there is some source of overheating.HP recommends to hoballahpdf edit the kernel command line (for rhel), but it does not work with Stretch.I have no idea why this was necessary, I had swords /dev/cdrom dvd and sg0 and they all mounted fine which basically means there we're 3 devices pointing to my optical drive and yet the installer is not able to detect.Either your system has no sensors, or they are not supported, or they are connected to an I2C or SMBus adapter craftmatic that is not supported.To get it working for me, I installed the kernel from experimental (2.6.36-rc6-amd64) and created the file /etc/nf with one line of content 'options cciss cciss_allow_hpsay' to get the cciss driver to not load if hpsa can handle the devices better, according to this discussion.Squeeze DL980 G7 SAS Hotplug o Worked mostly fine, needs firmware-netxen.Installation report in #783066 Daily Builds Daily builds are available from the d-i devel page.AMD Opteron Processor (X3xxx) stretch-4.9.0-4-amd64-netinst, nothing unusual in kernel logs.Had to set "Enable sata ahci" swords under "System Options" in bios to get it booting from hard drive.Curl m/SDR/hpPublicKey1024.pub apt-key add - curl m/SDR/hpPublicKey2048.pub apt-key add - curl m/SDR/hpPublicKey2048_key1.pub apt-key add - curl apt-key add - warning - the Debian repository is not always up to date.
04:00.0 raid bus controller 0104: Hewlett-Packard Company Smart Array G6 controllers 103c:323a (rev dl380 g4 maintenance guide 01) Subsystem: Hewlett-Packard Company Smart Array P410i 103c:3245 Kernel driver in use: hpsa 14:00.0 raid bus controller 0104: Hewlett-Packard Company Smart Array G6 controllers 103c:323a (rev 01) Subsystem: Hewlett-Packard Company Smart Array.
2) Tape Autoloader not detected until installed kernel.6.3 from Jessie backports.
Take notice that /dev/cciss/c0d0, likely your boot device, may suddenly show up as /dev/sda instead.